Ironwood-electronics Clip Use Instructions Manuel d'utilisateur
Naviguer en ligne ou télécharger Manuel d'utilisateur pour Matériel Ironwood-electronics Clip Use Instructions. Ironwood Electronics Clip Use Instructions User Manual Manuel d'utilisatio
- Page / 2
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
CLEANING THE CLIP
Clean the Clip contacts before each installation. Debris
on the contacts can interfere with its function.
INSTALLING THE CLIP
Extra care is required the first time you install the Clip. Since the chip package has not had previous intrusion
between the legs, more force than usual is required during installation. This is due to the fact that there is
excess solder from the plating process on the sides of the legs. Once the Clip has been inserted on a chip
package far less force will be required.
Use grounded wrist straps and mats when installing or performing any service to your Clip adaptor.
Electrostatic discharge can damage electronic components.
1. Clean the Clip as described above.
2. Allow the Clip to seek its own alignment by resting it on the chip package.
3. Rotate the Clip back and forth, to allow a tactile indication when the sharp tips of the contacts are cor-
rectly positioned between the legs of the chip package.
Installation of the Clip with any improper alignment can result in damage to the chip package legs and the
Clip itself. Avoid damage by ensuring proper positioning as shown. If a transition board or flexible cable
are attached to the Clip during installation, the tactile response is diminished and greater care must be
taken with initial positioning.
CAUTION
CAUTION
CLEANING THE CLIP
Clean the Clip contacts before each installation. Debris
on the contacts can interfere with its function.
INSTALLING THE CLIP
Extra care is required the first time you install the Clip. Since the chip package has not had previous intrusion
between the legs, more force than usual is required during installation. This is due to the fact that there is
excess solder from the plating process on the sides of the legs. Once the Clip has been inserted on a chip
package far less force will be required.
Use grounded wrist straps and mats when installing or performing any service to your Clip adaptor.
Electrostatic discharge can damage electronic components.
1. Clean the Clip as described above.
2. Allow the Clip to seek its own alignment by resting it on the chip package.
3. Rotate the Clip back and forth, to allow a tactile indication when the sharp tips of the contacts are cor-
rectly positioned between the legs of the chip package.
Installation of the Clip with any improper alignment can result in damage to the chip package legs and the
Clip itself. Avoid damage by ensuring proper positioning as shown. If a transition board or flexible cable
are attached to the Clip during installation, the tactile response is diminished and greater care must be
taken with initial positioning.
CAUTION
CAUTION
CLEANING THE CLIP
Clean the Clip contacts before each installation. Debris
on the contacts can interfere with its function.
INSTALLING THE CLIP
Extra care is required the first time you install the Clip. Since the chip package has not had previous intrusion
between the legs, more force than usual is required during installation. This is due to the fact that there is
excess solder from the plating process on the sides of the legs. Once the Clip has been inserted on a chip
package far less force will be required.
Use grounded wrist straps and mats when installing or performing any service to your Clip adaptor.
Electrostatic discharge can damage electronic components.
1. Clean the Clip as described above.
2. Allow the Clip to seek its own alignment by resting it on the chip package.
3. Rotate the Clip back and forth, to allow a tactile indication when the sharp tips of the contacts are cor-
rectly positioned between the legs of the chip package.
Installation of the Clip with any improper alignment can result in damage to the chip package legs and the
Clip itself. Avoid damage by ensuring proper positioning as shown. If a transition board or flexible cable
are attached to the Clip during installation, the tactile response is diminished and greater care must be
taken with initial positioning.
CAUTION
CAUTION
CLEANING THE CLIP
Clean the Clip contacts before each installation. Debris
on the contacts can interfere with its function.
INSTALLING THE CLIP
Extra care is required the first time you install the Clip. Since the chip package has not had previous intrusion
between the legs, more force than usual is required during installation. This is due to the fact that there is
excess solder from the plating process on the sides of the legs. Once the Clip has been inserted on a chip
package far less force will be required.
Use grounded wrist straps and mats when installing or performing any service to your Clip adaptor.
Electrostatic discharge can damage electronic components.
1. Clean the Clip as described above.
2. Allow the Clip to seek its own alignment by resting it on the chip package.
3. Rotate the Clip back and forth, to allow a tactile indication when the sharp tips of the contacts are cor-
rectly positioned between the legs of the chip package.
Installation of the Clip with any improper alignment can result in damage to the chip package legs and the
Clip itself. Avoid damage by ensuring proper positioning as shown. If a transition board or flexible cable
are attached to the Clip during installation, the tactile response is diminished and greater care must be
taken with initial positioning.
CAUTION
CAUTION
Position contacts between legs
Gravity only
Slight rotation without pressure
Ironwood Electronics, Inc.
Ironwood Electronics, Inc.
1
CLIP USE INSTRUCTIONS
1. Use a common toothbrush to remove any dust
between the contacts. The individual contacts are
engineered to be durable; nevertheless take appro-
priate care when brushing them to avoid damage.
2. Use precision dusting cleaner (also known as inert
dusting gas or compressed air in a can) to remove
debris loosened by the brushing.
1
2
Résumé du contenu
Page 1 - CLIP USE INSTRUCTIONS
CLEANING THE CLIPClean the Clip contacts before each installation. Debrison the contacts can interfere with its function.INSTALLING THE CLIPExtra care
Page 2
INSTALLING THE CLIP (CONT)4. Apply a constant downward force after the contacts are centered between the legs.Proper seating of the contacts is propor
Produits connexes et manuels pour Matériel Ironwood-electronics Clip Use Instructions
Matériel Ironwood-electronics GHZ LGA Socket (-M) Assembly Instructions Manuel d'utilisateur
(1 pages)
(1 pages)
Matériel Ironwood-electronics Solder Column Interface Soldering Techniques Manuel d'utilisateur
(0 pages)
(0 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.057 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels